Flushmate M-101526-F31 FM III 503 Pressure Assist tank less Handle for most O...

Description

Flushmate M-101526-F31 FM III 503 Pressure Assist tank less Handle for most OEM 2 piece toilets using Flushmate
Work Instruction: Replacement Instructions for Two Piece Flushmate Tanks Products: Two Piece Toilet Applications (M-101XXX Models, Series: 501A, 501B, 503)Instructions: Turn off water at the supply stop. Flush the toilet to relieve water and air pressure from the Flushmate system. Disconnect water supply line from the supply shank and remove the lock nut that holds the supply shank in place. The supply shank protrudes from the bottom of the china tank on the left hand side.If necessary, disconnect the Flushrod from the flush-handle linkage. Remove the screws that attach the Flushrod to the Flushmate and use them to attach the Flushrod to the new Flushmate.Loosen the nuts on the bolts protruding from the underside of the toilet, below the china tank. These nuts should be loosened much like lug nuts on an automobile wheel; alternate between them instead of completely removing one at a time.Once the nuts have been removed, lift the china tank straight up off of the bowl. Empty any residual water that may have accumulated in the china tank into the china bowl. Place the china tank down flat on its backside on a security location.Remove the tank to bowl gasket (thick, spongy doughnut-type) from the Discharge Extension and unscrew large lock-nut on the bottom center of the china tank. A spanner wrench works well for this, but any tool that will spread to accommodate the 3 plastic locknut will work.Slide the Flushmate system out of the china tank.Place new tank to tank gasket (flat rubber gasket with ribs on one side) on new Flushmate with the ribs facing downward. Some tank to tank gaskets do not have ribs, installation of this gasket is universal. Slide the Flushmate system into the china tank. It's best to insert the supply shank into the china tank first and than the Flushmate vessel.Screw both lock-nuts onto the exposed threads (supply shank and discharge extension) on the bottom end of the china tank.Place the tank to bowl gasket onto the exposed discharge extension and reattach tank to bowl.Attach brass washers and hex nuts to each bolt (making sure you put the washers on before the hex nuts) and tighten securely. When tightening the tank to bowl nuts, use the alternating method while putting downward pressure on each side as you tighten the nuts on that side. In effect, you will be rocking the system in the direction of the nuts you are tightening. You must get the bolts tight enough to prevent any leakage (when flushed) between the tank and the bowl, but not so tight that you risk breaking the china.Reattach water supply line to the supply shank and turn on the supply stop. Wait for Flushmate to set up (fill with water and stop cycling ) and flush the toilet. If the Flushmate doesn't set up and water continues to run through it, you will need to adjust the cartridge and perhaps the actuator cap. See the owners manual for adjustment
Product Features
For ALL OEMs except Kohler K 4404 tank and Gerber 28-385 tank ; CAUTION does NOT work in One-piece Fixtures ; Tank-to-Bowl Gasket
It does NOT fit 10 Inch rough-in tanks, only 12 Inch rough-in tanks. Rough-in refers to the distance from the wall to the bolts at the center of the drain.
ONLY used on model 503 Flushmate Systems 1.6 gpf tanks
Does not include Cartridge
Shipping:
Shipping is complimentary within the lower 48 US States.
We Do Not Ship to PO/APO Boxes, HI or Alaska
We Do Not Ship Outside of the Continental US
All items ship within 24-72 hours of Payment
For large items that require Freight shipping a valid phone number is required to call and schedule your delivery
Terms of Sale and Feedback:
Feedback is extremely important to us and eBay
If you are satisfied with our transaction, please take a moment to leave Positive Feedback. YOUR Satisfaction is our #1 Priority!
If there are any issues, PLEASE contact us BEFORE leaving a neutral or negative rating so that we may resolve any concerns.
We PROMISE we can make you happy if you give us a fair chance.
Returns / Concerns:
All items qualify for returns within 14 - 30 days of receipt. Buyer is responsible for return shipping on any item that is not damaged
Please be sure this is an item you want before making your purchase. Customer Satisfaction is our TOP priority!
All items are IN STOCK at time of listing.
Inventory on eBay changes constantly and it is impossible to maintain a perfectly accurate count of all items.
Please do not penalize us if we have to issue you a refund!
Thank You For Your Business!