Geeetech 3D Touch Auto-Leveling SensorV3.2 Hot Bed Level for 3D Printer Free Tax

Description

Geeetech Auto Bed Leveling Sensor Device With High Compatibility Ship from US
Here is the instructions of 3D touch, you can refer to it,click
here
Description:
3DTouch auto leveling sensor
3DTouch is an auto leveling sensor for 3D Printers that can precisely measure the tilt of your print surface. It can greatly improve the printing precision of your 3D Printer.
3DTouch features simple, smart and precise. It could work with nearly any kind of bed materials, such as glasses, woods, metals and so on.
The main functions and controls of 3DTouch are the same as most auto bed leveling sensors, which consists of a RC servo and a micro switch, thus, 3DTouch can be used on almost every 3D printer control board.
By using progressively designed solenoid and hall sensor, 3DTouch can integrate high precision in such a simple structure. To make it more user-friendly and to bring you more enjoyable printing experience we add many smart functions such as self-test, false alarm, alarm release and test mode for M119.
Please note:
3D touch auto leveling sensor is not plug_and_play; you will need to do some modification to your firmware and for some control board, you may need to do some soldering work to the connector. We have prepared the pins for you.
For detailed instructions, please refer to the user manual. If you need any help, please feel free to contact us.Thank you.
Features:
1 Simple
3DTouch can be easily applied, since it has a small and simple structure. Gathering information & firmware setting will be an easy task, because 3DTouch works as usual auto bed leveling sensor.
2 Smart
Self-test: The push pin is operated two times to test when the power is on
Alarm: The LED light blinks if a problem found on a self-test or on an operation
3 High-precision
3DTouch’s Standard Deviation in repeatability is around 0.005mm, at that precise.
If you choose 3DTouch, your 3D printer will be high-class masterpiece, giving you an enjoyable experience.
4. Innovative Solenoid: Ultra Power Saving
On idle state, while the push-pin is whether pulled out or retracted, there are not any electric current flowing on solenoid, and standby electric current in the whole device is below 15mA on average, whereas on working state, while the pin is moving in sudden about 100ms, under 300mA flows in the device.
Low power consumption even further drops joule heating, preventing from heat problem.
5 Technologies
3DTouch consists of Atmel ATtiny13A, solenoid, and a push pin.
6 wide Selection of Bed
3DTouch does not uses either optical, nor proximity (inductive/capacitive) sensor.
3DTouch is controlled by Hall Effect, providing high precision. Thus the bed material can be selected freely.
7 Optimized structure: Larger Build Size
3DTouch is a small and technology-intensive one. Build size can be set larger than other existing auto bed leveling sensor.
3DTouch uses existing RC Servo motor signal intactly, so just plug 3DTouch on the same pins after removing servo motor.
Specifications:
Voltage: 5V
Current: 15mA
Max. Current: 300mA
Cable length: 150mm
Net Weight: 10g
Shipping weight: 25g
Wiring
3-pin: Brown (-, GND), Red (+5V), Orange (control signal)
2-pin: Black (-, GND), White (Z min)
Package list:
1 X 3DTouch Auto leveling sensor
1 X 3Pin Straight Pin
1 X 2Pin Straight Pin
2 X Screw & Nut & Washer
2 X Dupont Housing Shell 3Pin
2 X Dupont Housing Shell 2Pin
3 X Dupont Housing Shell 1Pin
14 X Dupont Terminal
1 X 10KΩ 1/8W Resistor
Operate condition
3DTouch can be operated in the following condition.
One I/O for control (PWM or Software PWM)
One I/O for Z min (Z Probe)
GND and +5V power
Caution
Additional power supply will be needed in case your board does not supply enough amperage.
Electronic devices can be damaged or even destroyed if connected to wrong polarity. [wrong terminal connect to 5V(+) and GND(-)]
Pulling/pushing hard on the push-pin can damage 3DTouch and make it less accurate.
Fix push-pin with locking paint after reassembling or adjusting core.
Do not remove or deform elastic material attached on the push-pin.
Payment
Delivery details
Terms of sales
About us
Contact us
Payment
Payment must be received within 7 business days of auction closing,
or a unpaid case will be opened.
Delivery details
1. This items will be sent from Los Angeles, United States.
2. Please confirm you are putting a correct and complete shipping address here.You are resposible for extra charge if your package been returned because of wrong address.
Terms of sales
Please confirm you are putting a correct and complete shipping address here.You are resposible for extra charge if your package been returned because of wrong address. If packages return because of wrong address,you will have to bear extra cost of shipping.
About us
Getech Co .,Ltd( Geeetech) is an innovative, technology oriented enterprise that is specialized in the R&D, manufacturing and sales of 3D printer and the spare parts of 3D printer. Geeetech has been one of the most prominent rising star in the area of 3D printing since founded in 2011.
Geeetech advocates making 3D printing easy and economical and we are hoping to help more enthusiasts get easy access to the wonderful world of 3D printing.
Contact us
1. We are always here for you,offering friendly, comprehensive customer service every step of the way. Please follow the good eBay practice to contact us if any doubts and problems.We sincerely hope our item and customer service can give you the BEST BUYING EXPERIENCE on eBay.
2. We greatly appreciate your POSITIVE feedback.
Please do NOT leave negative or neutral feedback without any contact.
On May 10, 2022 at 20:24:18 PDT, seller added the following information: