National Instruments NB-MIO-16 Multifunction DAQ I/O Macintosh Mac NuBus Board

Description

National Instruments NB-MIO-16 Multifunction DAQ I/O Mac NuBus Board
Comes with a manual and what you see in the pictures. If you don't see it, you probably wont get it.
Specifications are from National Instruments and may vary slightly due to upgrades, options, or revisions this unit may or may not have.
This board was removed from service in working condition.
The Unit's Serial Number Tag Reads:
Model Number:
NB-MIO-16
Part Number:
180500-01
Revision:
E1
Serial Number:
007483
Analog Input Specifications:
Number of Input Channels:
16 single-ended, 8 differential
Analog Resolution:
12-bit, 1 in 4,096
Type of ADC:
Successive-approximation
Relative Accuracy:
±1 LSB maximum over temperature, ±3/4 LSB typical (nonlinearity + quantization error)
Integral Nonlinearity:
±1/2 LSB maximum
Differential Nonlinearity (DNL):
±1 LSB maximum (no missing codes over temperature); typical ±1/2 LSB
Differential Analog Input Ranges:
±10 V, ±5 V, or 0 to +10 V, jumper-selectable
Analog Input Range:
±12 V
Common-Mode Range:
±7 V, ±9.5 V, or ±7 V, for respective differential analog input ranges.
Instrumentation Amplifier:
Input Bias Current:
±25 nA maximum
Input Offset Current:
±15 nA maximum
Input Impedance:
1 GΩ
Gain Ranges:
1, 2, 4, and 8 for NB-MIO-16H. 1, 10, 100, and 500 for NB-MIO-16L. Software-selectable
Gain Accuracy:
(includes pot adjustment range)
Gain = 1:
±0.83% of full scale, adjustable to zero
Gain > 1:
±0.85% of full scale, ±0.08% of full scale maximum when gain error adjusted to zero at gain = 1
Temperature Drift:
36 ppm/°C
Input Offset Voltage (includes pot adjustment range):
±50 mV for gain 1, adjustable to zero. ±25 mV for gain 2. ±15 mV for gain 4. ±10 mV for gain 8. ±5 mV for gain 10. ±2 mV for gain 100. ±1.5 mV for gain 500
Temperature Drift:
160 µV/°C + 6 µV/°C * gain
Other System Offset Voltage (includes pot adjustment range):
±85 mV for ±10 V range, adjustable to zero. ±45 mV for ±5 V range. ±30 mV for 0 to +10 V range.
System Noise (figures are for 20 V range; multiply by two for 10 V range):
0.15 LSB for gains 1 to 10. 0.25 LSB for gain 100. 0.5 LSB for gain 500
Analog Output Specifications:
Number of Output Channels:
2
Type of DAC:
12-bit, multiplying
Relative Accuracy (nonlinearity):
±1/2 LSB maximum, ±1/4 LSB typical
Differential Nonlinearity:
±1 LSB maximum (monotonic over temperature), ±1/5 LSB typical
Gain Error:
±0.77% of full scale, adjustable to zero (includes pot adjustment range, but excludes reference)
Voltage Offset:
±64 mV bipolar mode, ±32 mV unipolar mode, adjustable to zero (includes pot adjustment range)
Internal Voltage Reference:
10 V (±100 mV maximum); 25 ppm/°C drift
Output Voltage Ranges:
0 to +10 V, unipolar mode; ±10 V, bipolar mode (jumper-selectable)
Current Drive Capability:
±2 mA
Output Settling Time to 0.01%:
20 µs for a 10 V step. ±40 µs for a 20 V step.
Output Slew Rate:
2.5 V/µsec
Output Noise:
500 µV rms, DC to 20 MHz
Output Impedance:
0.1 Ω maximum
Digital I/O Specifications:
Compatibility:
TTL-compatible
Output Current Source Capability:
Can source 2.6 mA and maintain V
OH
at 2.4 V
Output Current Sink Capability:
Can sink 24 mA and maintain V
OL
at 0.5 V max
Timing I/O Specifications:
Number of Channels:
Four: 3 counter/timers, 1 frequency output
Resolution:
16-bit for 3 counter/timers, 4-bit for frequency output channel
Base Clock Available:
1 MHz, 100 kHz, 10 kHz, 1 kHz, 100 Hz
Base Clock Accuracy:
±0.01%
Compatibility:
TTL-compatible inputs and outputs. Counter gate and source inputs are pulled up with 4.7-kΩ resistors onboard.
Counter Input Frequency:
6.9 MHz maximum (145 ns period) with a minimum pulse width of 70 ns
Power Requirement (from Macintosh NuBus) Specifications:
Power Consumption:
1.5 A typical at +5 VDC
Physical Specifications:
Board Dimensions:
12.8 by 4.0 in.
I/O Connector:
50-pin male ribbon-cable connector
Operating Environment Specifications:
Component Temperature:
0° to 70°C
Relative Humidity:
5% to 90% noncondensing
Storage Environment Specifications:
Temperature:
-55° to 150°C
Relative Humidity:
5% to 90% noncondensing
For Domestic Customers: Packaging, handling, and order processing included in shipping in all domestic shipments as quoted by the shipping calculator. For International Customers there is a {{detail_product_description}}.00 minimum for packaging, handling, and order processing. International shipping to be determined by destination.
Prior to shipment I will need to know the following information (filled out on a form that I will send you) for International Customers or Packages/Freight being Forwarded internationally. International customers may also be subject to a freight forwarder form if applicable.:
(1) Are you the end-user of this item?
(2) If you are not the ultimate end-user of the item, please state the ultimate end user's name.
(3) What is the ultimate country destination?
03/24/15